 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 5.0V Surface Mount Crystal Clock Oscillator HSM6 XO 2111 Comprehensive Drive 2111 Comprehensive Drive Aurora, Illinois 60505 Aurora, Illinois 60505 Phone: 630- 851- 4722 Phone: 630- 851- 4722 Fax: 630- 851- 5040 Fax: 630- 851- 5040 www.conwin.com www.conwin.com Features: RoHS Compliant 1.0 to 80 MHz 5.0V Operation Tri-State Enable/Disable Function Overall Frequency Tolerance: HSM61 25 ppm, HSM62 50 ppm, HSM63 100 ppm Temperature Range: -40 to 85C Ceramic Surface Mount Package Tape and Reel Packaging US Headquarters: 630-851-4722 European Headquarters: +353-61-472221 The Connor-Winfield models HSM61, HSM62, and HSM63 are 7.5mm x 5mm, 5.0V HCMOS, Surface Mount, Fixed Frequency Crystal Oscillators (XO) designed for use in all applications requiring precision clocks. The RoHS compliant surface mount package is designed for high-density mounting and is optimum for mass production Absolute Maximum Ratings Parameter Storage Temperature Supply Voltage (Vcc) Minimum -55 -0.5 Nominal Maximum 125 7.0 Units C Vdc Notes Operating Specifications Parameter Frequency Range (Fo) Frequency Tolerance HSM61 HSM62 HSM63 Operating Temp Range Supply Voltage (Vdd) Supply Current (Icc) 1.8 to 31.999 MHz 32.0 to 49.999 MHz 50 to 80.0 MHz Minimum 1.0 -25 -50 -100 -40 4.5 Nominal Maximum 80 25 50 100 85 5.5 27 45 75 Units MHz ppm Notes 1 5.0 - C Vdc mA Input Characteristics Parameter Enable Voltage - (Vih) Disable Voltage - (Vil) Enable Time Disable Time Minimum 2.2 Nominal Maximum 0.8 100 100 Units Vdc Vdc nS nS Notes 2 HCMOS Output Characteristics Parameter Load (Voh) Voltage High (Vol) Low (loh) Current High (lol) Low Duty Cycle at 50% of Vcc Rise / Fall Time 10% to 90% Start-Up Time Jitter Minimum 4.50 -16 45 Nominal 50 Maximum 50 0.55 16 55 5 10 5 Units pF Vdc mA % nS mS pS RMS Notes Bulletin Page Revision Date SM036 1 of 2 13 18 Dec 2007 Notes: 1. Inclusive of calibration @ 25C , frequency vs temperature stability, supply voltage change, load change, shock and vibration, 10 years aging. 2. Oscillator output is enabled with no connection on pad 1 Specifications subject to change without notice. All dimensions in inches. (c) Copyright 1998 The Connor-Winfield Corporation 2111 Comprehensive Drive Aurora, Illinois 60505 Phone: 630- 851- 4722 Fax: 630- 851- 5040 www.conwin.com Package Characteristics Package Hermetically sealed ceramic package and metal cover Suggested Pad Layout Environmental Characteristics Temperature Cycle The specimen shall meet electrical characteristics after tested 5 cycles of -55C / 30 minutes and +125C / 30 minutes Hermetical No bubbles appear in Flourinert (FC-43) at 125C 5C for 5 minutes Solvent Resistance Marking will withstand immersion in Isopropyl Alcohol or Trichloroethylene Soldering General Conditions 260C max x 10 sec max x 2 times max or 230C max x 180 sec max x 1 time Typical Operation Data (Vapor phase reflow) 20 to 100 sec up to 215C, 50 sec at 215C, then down to room temperature per 1 to 5C / sec Bypass capacitor, C-by, should be ceramic capacitor .01 uf Test Circuit OSCILLOSCOPE PROBE Mechanical Characteristics Mechanical Shock MIL STD 883 Method 2002 Vibration The specimen shall meet electrical characteristics after tested by the following conditions: 10-55Hz 1.5mm Amplitude, 55-2000 Hz 20 G's, 2 hours for each plane Thermal Shock After applied Thermal Shock of 260C max x 10 sec max x 2 times, or 230C max x 180 sec max, the specimen shall meet electrical characteristics Solderability (EIAJ-RCX-0102.101 Condition 1a) 1) Flux: MIL-F-14256 (WW Rosin=25%, Isopropyl Alcohol = 75%) 2) Solder: QQ-S-571 (Sn = 63%, Pb = 37%) 3) Solder bath temperature: 235C 5C 4) Depth of immersion: Up to electrical terminal 5) Immersing time: Within 2 sec 0.5 sec into solder bath After performing the above procedures, a newly soldered coverage shall be greater than 90% POWER SUPPLY OSC FREQ COUNTER INPUT FOR E/D Output Waveform Ordering Information HSM Type: Clock 7.5x5.0mm Package SYMMETRY 6 Temperature Range: 6 = -40 to 85C 1 Frequency Tolerance: 1 = 25 ppm 2 = 50 ppm 3 = 100 ppm Supply Voltage: Omit = 5.0 Vdc 044.736M Output Frequency: Frequency Format -xxx.xM Minimum * -xxx.xxxxxxM Maximum* *Amount of numbers after the decimal point. M = MHz Example: To Order an HSM61 with an output frequency of: 4 MHz = HSM61-004.0M 44.736 MHz = HSM61-044.736M 125 MHz = HSM61-125.0M Tape and Reel Dimensions Pin Connections 1: Enable/Disable 2: Ground 3: Output 4: Vcc Dimensional Tolerance: .02" (.508mm) .005"(.127mm) Bulletin Page Meets EIA-481A and EIAJ-1009B 2,000 PCS/Reel Specifications subject to change without notice. All dimensions in inches. (c) Copyright 1998 The Connor-Winfield Corporation Revision Date SM036 2 of 2 13 18 Dec 2007 |
Price & Availability of HSM6
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |